Nikon D5500 For Dummies
Book image
Explore Book Buy On Amazon

Here’s an introduction to your camera’s most important exposure guide: the exposure meter. The meter on your Nikon D5500 tells you whether the camera thinks your picture will be properly exposed at your chosen exposure settings.

However, if and when the meter appears depends on whether you shoot in the M, P, S, or A exposure mode:

  • M mode: The meter is always present in the Information and Live View displays and also appears in the viewfinder data display.

    In M exposure mode, the exposure meter appears in the Information and Live View displays.
    In M exposure mode, the exposure meter appears in the Information and Live View displays.

    You can see a close‐up look at how the meter looks in the viewfinder.

    The bars under the meter indicate the amount of under or overexposure.
    The bars under the meter indicate the amount of under or overexposure.
  • P, S, and A modes: The meter doesn’t appear unless the camera anticipates an exposure problem — for example, if you’re shooting in S (shutter‐priority autoexposure) mode, and the camera can’t select an f‐stop that will properly expose the image at your chosen shutter speed and ISO. You also see the meter if you enable Exposure Compensation. In that case, the meter indicates how much Exposure Compensation is being applied.

Either way, here’s what you need to know about using the meter:

  • Waking up the meter: By default, the meter appears when you press the shutter button halfway and then turns off automatically after 8 seconds of inactivity to save battery power. To wake up the meter, just give the shutter button another half‐press.

    You can adjust the meter’s auto shutdown timing via the Auto Off Timers option, found in the Timers/AE Lock section of the Custom Setting menu.

  • Reading the meter: The minus‐sign end of the meter represents underexposure; the plus sign, overexposure. If the little notches under the meter fall to the left of 0, the image will be underexposed. If the notches move to the right of 0, as shown in the second example, the image will be overexposed. When all notches except the center bar disappear, you’re good to go.

    A couple of details to note:

    • The markings on the meter indicate exposure stops. The squares on either side of the 0 represent one full stop each. The small lines below, which appear only when the meter needs to indicate over‐ or underexposure, break each stop into thirds. So the middle readout, for example, indicates an overexposure of 1 and 2/3 stop. The left readout indicates the same amount of underexposure.

      The third‐stop display assumes that you haven’t asked the camera to present exposure data in half‐stop increments, in which case you see just one bar between each stop. Again, this feature is controlled by the EV Steps for Exposure Cntrl option, located in the Exposure section of the Custom Setting menu.

    • If a triangle appears at the end of the meter, the amount of over or underexposure exceeds the twostop range of the meter. In other words, you have a serious exposure problem.

    • You can reverse the meter orientation. For photographers used to a camera that orients the meter with the positive (overexposure) side appearing on the left and the negative (underexposure) side on the right — the design that Nikon used for years — the D5500 offers the option to flip the meter to that orientation. This option also lies on the Custom Setting menu, on the Controls submenu. Look for the Reverse Indicators option.

      You can reverse the meter orientation.
      You can reverse the meter orientation.
  • Understanding how exposure is calculated: The information the meter reports is based on the Metering mode, which determines which part of the frame the camera considers when calculating exposure. At the default setting, exposure is based on the entire frame, but you can select two other Metering modes.

    There’s one metering quirk to note with respect to Live View photography: In Live View mode, metering may be calculated differently for some scenes than when you use the viewfinder. The rationale is to produce an exposure that’s close to what you see in the live preview, which gets darker or lighter as you change exposure settings in an attempt to simulate the final exposure.

    However, don’t trust the preview because it can be deceiving depending on the ambient light in which you’re viewing the monitor. In addition, when you apply Exposure Compensation, an option that produces a brighter or darker image in the P, S, and A modes, the monitor can’t adjust itself to accommodate the full range of Exposure Compensation settings. Long story short: The meter is a more accurate indication of exposure than the live preview.

Finally, keep in mind that the meter’s suggestion on exposure may not always be the one you want to follow. For example, you may want to shoot a backlit subject in silhouette, in which case you want that subject to be underexposed. In other words, the meter is a guide, not a dictator.

About This Article

This article is from the book:

About the book author:

Julie Adair King's history as a digital photography author dates back to 1997 with the publication of the first edition of Digital Photography For Dummies. Since then she has authored over 50 books on digital photography, cameras, and photo editing and design software.

This article can be found in the category: